Vernier Calipers

Product Details:

• With no annoying origin restoration necessary,a measurement can be started any time and there is no restriction on operating speed.
• World’s unique* solar-powered SuperCaliper that is eco-friendly with no battery.
• According to Mitutoyo investigation in January, 2005
• The impact resistance of the display unit has been increased for improved usability in workshop conditions.
• IP67 protection assures waterproof reliability.
• This SuperCaliper uses components that do not contain harmful substances and is compatible with RoHS Directives.
• Supplied in fitted plastic case.

• Origin-set, inch/mm conversion (inch/mm models)
• Alarm: Counting value composition error

• 05CZA624: SPC cable with data switch (1m / 40”)
• 05CZA625: SPC cable with data switch (2m / 80”)

• Level 6: Dust-tight
• No ingress of dust.
• Level 7: Protected against the effects of temporary immersion in water.
• Ingress of water in quantities causing harmful effects shall not be possible when the enclosure is temporarily immersed 1 meter in water under standardized conditions of pressure and time (30 min.).

Specifications: 

Product Details:

• Mitutoyo's Absolute Solar Digimatic Caliper retains its origin point even if the display turns off for the entire life of the caliper. At 60
• Lux and up the ABSOLUTE solar caliper is, turned on ready to start measurement.
• No more repeated zero setting caused by the shortage of light intensity.
• Hard-coated solar panel for safe operation.
• No fear for overspeed errors.
• With thumb roller.
• Supplied in fitted plastic case.

• Origin-set, Data hold, Data output, inch/mm conversion (inch/ mm models)
• Alarm: Counting value composition error

• 959143: Data hold unit (SPC output model only)
• 959149: SPC cable with data switch (1m / 40”)
• 959150: SPC cable with data switch (2m / 80”)

Specifications:

Product Details:

• Can be used in workshop conditions exposed to coolant, water, dust or oil.
• Easy to use - no need to wipe or clean the scale.
• Advanced design styling.
• Incorporates absolute measurement system.
• Automatic power-on/off.
• Data output function.
• With thumb roller.
• Supplied in fitted plastic case.

• Origin-set, Zero-setting, Automatic power on/off, Data output, inch/mm conversion (inch/mm models)
• Alarm: Low voltage, Counting value composition error

• 05CZA624: SPC cable with data switch (1m / 40”)
• 05CZA625: SPC cable with data switch (2m / 80”)

Product Details:

• Mitutoyo's absolute Digimatic Caliper is the next generation of electronic calipers.
• It keeps track of its origin point once set. Whenever turned on, the large LCD displays the actual slider position ready to start measurement.
• No more repeated zero setting is necessary with the absolute encoder technology, as well as no more concern for over speed errors.
• Large and clear LCD readout.
• The ZERO/ABS key allows the display to be Zero-Set at any slider position along the scale for incremental comparison measurements.
• This switch will also allow return to the absolute (ABS) coordinate and display of the true position from the origin point (usually jaws-closed point).
• Data Hold Unit (959143) is optional.
• Carbide-tipped jaw type calipers are also available.
• With thumb roller. Except 500-500-10, 500-501-10,500-502-10.
• Supplied in fitted plastic case. Except 1000mm / 40” supplied in wooden case.

• Origin-set, Zero-setting, Data output, inch/mm conversion (inch/mm models ONLY)
• Alarm: Low voltage, Counting value composition error

• 959143: Data hold unit
• 959149: SPC cable with data switch (1m / 40”)
• 959150: SPC cable with data switch (2m / 80”)

Product Details:

• The rounded faces of the jaws are ideal for accurate ID (inside diameter) measurement.
• Inside and outside measurements can be directly read from the upper and lower slider graduations (Series 160).
• With fine-adjustment carriage type is available (Series 160).
• Parallax-free vernier scale type is available for easy and positive measurement (Series 160).
• With SPC output (Series 550).
• Supplied in fitted plastic case. Except 1000mm / 40” supplied in wooden case.

• Origin-set, Zero-setting, Data output,
• inch/mm conversion (on inch/metric models only)
• Alarm: Low voltage, Counting value composition error

• 959143: Data hold unit
• 959149: SPC cable with data switch (40” / 1m)
• 959150: SPC cable with data switch (80” / 2m)
• 05CZA624: SPC cable with data switch (40” / 1m) for IP67 model
• 05CZA625: SPC cable with data switch (80” / 2m) for IP67 model

Product Details:

• The rounded faces of the jaws are ideal for accurate ID (inside diameter) measurement.
• With SPC output.
• Supplied in fitted plastic holster in carton.18"/450mm and larger supplied wooden case.

• Origin-set, Zero-setting, Data output, inch/mm conversion (inch/mm models)
• Alarm: Low voltage, Counting value composition error

• 05CZA624: SPC cable with data switch (1m / 40”)
• 05CZA625: SPC cable with data switch (2m / 80”)

Product Details:

• Origin-set, Zero-setting, Presetting, Offsetting, Data hold,
• Automatic power on/off
• Data output, inch/mm conversion (inch/mm models)
• Alarm: Low voltage, counting value composition error

• 05CZA624: SPC cable (straight, 1m / 40”)
• 05CZA625: SPC cable (straight, 2m / 80”)

Product Details:

• Origin-set, Zero-setting, Presetting, Offsetting, Data hold, Data output, inch/mm conversion (inch/mm models)
• Alarm: Low voltage, Counting value composition error

• 05CZA624:SPC cable with data switch(40in/1m)
• 05CZA625:SPC cable with data switch (80in/2m)
• 914055: Centerline attachments (mm)*
• 914056: Centerline attachments (inch)*
• 914057: Pointed ID measuring attachments (mm)*
• 914058: Pointed ID measuring attachments (inch)*
• 914053: Attachment clamps (for models up to 600mm/24” range)
• 914054: Attachment clamps (for models over 600mm/24” range)
• Attachment clamps are required and not available for long jaw type.

• Lightweight Digimatic Calipers that employ CFRP (Carbon Fiber Reinforced Plastics)in the beam and jaws.
• Highly durable and easy to handle.
• The range of applications can be expanded by using the optional attachments.
• Direct readout of ID measurements from the LCD. (Offset value can be set easily by pressing the Offset key.)
• Preset function for setting a desired starting point.
• With SPC data output.
• Special model available with ceramic jaws which are suitable for measuring abrasive
  and magnetic products.
• Supplied in fitted wooden case.

Product Details:

• Main scale jaw can slide up and down to facilitate measu           ement of stepped sections. (Hard-to-get-at dimensions such as A, B, C can be accurately measured.)
• With depth bar.
• With SPC data output. (series 573)
• Supplied in fitted plastic case.

Function of Digital Model:

• Origin-set, Zero-setting, Power On/Off, Data output, inch/mm conversion (inch/mm models)
• Alarm: Low voltage, Counting value composition error

• 05CZA624:SPC cable with data switch (1m/40”)
• 05CZA625:SPC cable with data switch (2m/80”)

Product Details:

• Specially designed for center to center distance measurements on the same and offset planes.
• Can also measure from edge to center.
• Hole diameter should be in the range of 1.5mm-10mm (.06"-.4").
• With SPC data output. (series 573)
• Supplied in fitted plastic case.

Function of Digital Model:

• Origin-set, Zero-setting, Power On/Off, Data output, inch/mm conversion (inch/mm models)
• Alarm: Low voltage, Counting value composition error

• 05CZA624: SPC cable with data switch (1m/40”)
• 05CZA625: SPC cable with data switch (2m/80”)

Product Details:

• Specially designed to measure the distance between two centers or the distance from an edge to center.
• Provided with jaws on the back of the slider, measurements can be read easily by looking down.
• Direct reading of pitch measurements is available due to the offset value setting function.
• With SPC data output.
• Supplied fitted in wooden case.

Function:

• Origin-set, Zero-setting, Power On/Off, Data output, inch/mm conversion (inch/mm models)
• Alarm: Low voltage, Counting value composition error

• 959143: Data hold unit
• 959149: SPC cable with data switch (1m)
• 959150: SPC cable with data switch (2m)

Product Details:

• Narrow tip jaws fit into very small grooves and tracks, making many previously difficult outside measurements far easier to obtain. With depth bar.
• With SPC data output. (Series 573)
• Supplied in fitted plastic case.
  
  

• Origin-set, Zero-setting, Power On/Off, Data output, inch/mm conversion (inch/mm models)
• Alarm: Low voltage, Counting value composition error

• 05CZA624: SPC cable with data switch (1m / 40”)
• 05CZA625: SPC cable with data switch (2m / 80”)

Product Details:

• The thin blade type jaws fit into very small grooves and making previously difficult outside measurements far easier to obtain.
• The OD measuring faces are carbide-tipped.
• With depth bar.
• With SPC data output. (Series 573)
• Supplied in fitted plastic case.
  
  

• Origin-set, Zero-setting, Power On/Off, Data output, inch/mm conversion (inch/mm models)
• Alarm: Low voltage, Counting value composition error

• 05CZA624: SPC cable with data switch (1m / 40”)
• 05CZA625: SPC cable with data switch (2m / 80”) 

Product Details:

• Point jaw type can measure wall thickness inside bores and recesses.
• Flat jaw type can measure grooves and recesses.
• With SPC data output. (Series 573)
• Supplied in fitted plastic case.

Function of Digital Model:

• Origin-set, Zero-setting, Power On/Off, Data output, inch/mm conversion (inch/mm models)
• Alarm: Low voltage, Counting value composition error

• 05CZA624: SPC cable with data switch (40” / 1m)
• 05CZA625: SPC cable with data switch (80” / 2m)

Product Details:

• Specially designed for inside measurements in hard-to-reach places.
• With SPC data output. (Series 573)
• Supplied in fitted plastic case. 18in /450mm and 24in/600mm supplied in wooden case.
  
  

• Origin-set, Zero-setting, Power On/Off, Data output, inch/mm conversion (inch/mm models)
• Alarm: Low voltage, Counting value composition error

• 05CZA624: SPC cable with data switch (1m)
• 05CZA625: SPC cable with data switch (2m)

Product Details:

• The ABSOLUTE Digimatic snap caliper features a spring-loaded mechanism to allow quick and efficient GO/NO-GO inspection for mass production parts..
• With SPC data output.
• Supplied in fitted plastic case.
  
  

• Origin-set, Zero-setting, Power On/Off, Data output, inch/mm conversion (inch/mm models)
• Alarm: Low voltage, Counting value composition error

• 959143: Data hold unit
• 959149: SPC cable with data switch (40” / 1m)
• 959150: SPC cable with data switch (80” / 2m)

Product Details:

• The “MyCAL-Lite” is an ideal measuring tool for DIY.
• The LCD screen allows error-free readout of measurements.
• With depth measuring bar.

Function:

• Zero-setting, Power on/off
• Alarm: Low voltage, Counting value composition error

Product Details:

• Due to the low measuring force these calipers are ideal for elastic or resilient workpieces such as plastic parts and rubber parts that standard calipers cannot measure.
• With SPC data output.
• Supplied in fitted plastic case.
  
  

• Origin-set, Zero-setting, Power On/Off, Data output, inch/mm conversion (inch/mm models)
• Alarm: Low voltage, Counting value composition error

• 959143: Data hold unit
• 959149: SPC cable with data switch (40” / 1m)
• 959150: SPC cable with data switch (80” / 2m)  

Product Details:

• The carbide-tipped jaws facilitate fine scribing on workpiece.
• With depth bar.
• With SPC data output. (Series 573)
• Supplied in fitted plastic case.
  
  

• Origin-set, Zero-setting, Power On/Off, Data output, inch/mm conversion (inch/mm models)
• Alarm: Low voltage, Counting value composition error

• 05CZA624: SPC cable with data switch (40” / 1m)
• 05CZA625: SPC cable with data switch (80” / 2m)

Product Details:

• The main scale jaw is a round bar that facilitates measurements of tube wall thickness.
• With SPC data output. (Series 573)
• Supplied in fitted plastic case.
  
  

• Origin-set, Zero-setting, Power On/Off, Data output, inch/mm conversion (inch/mm models)
• Alarm: Low voltage, Counting value composition error

• 05CZA624: SPC cable with data switch (40” / 1m)
• 05CZA625: SPC cable with data switch (80” / 2m)

Product Details:

• Long jaws for measuring hard-to-reach features.
• Fine adjustment for more accurate measurement
  (except 534-109 and 534-110)
• Supplied in fitted wooden case.

Specifications: 

Product Details:

• Measures OD (outside diameter), ID (inside diameter), depth, and steps.
• The small vernier face angle (14°) provides easy reading.
• Dual reading scales on vernier. (metric/inch and inch models only)
• Lock screw for holding thesliding jaw position.
• Carbide-tipped jaw type calipers are also available.
• Supplied with vinyl holster in fitted carton. Except 600mm / 24” models are carton only. 1000mm / 40” supplied in wooden case.

Specifications: 

Product Details:

• The slider moves only when the spring loaded thumb clamp is depressed.
• Can measure OD, ID, depth, and steps
• Supplied with vinyl holster in fitted carton.

Product Details:

• Provided with a fine-adjustment carriage to feed the slider finely.
• Can measure OD, ID, depth, and steps.
• Supplied with vinyl holster in fitted carton.

Specifications:

Product Details:

• New designed dial movement for ultra smooth sliding and high shock protection.
• Can measure OD, ID, depth, and steps.
• Lock screw for dial bezel and for holding the slding jaw position .
• Models available with carbide-tipped OD and ID jaws.
• Supplied in fitted plastic case.

Specifications:

Product Details:

• The jaws have round measuring faces for accurate ID measurement.
• With fine adjustment carriage to feed the slider finely. (without 160-130~134)
• Inside and outside measurements can be directly read from the upper and lower slider graduations, respectively.
• Supplied with vinyl holster in fitted carton. Except 300mm / 12”, 450mm/18” and 600mm/24” are fitted carton only.
• Over 600mm/24” supplied in wooden case.

Specifications:

Product Details:

• Pairs of conical probes are specially designed for Digimatic
• Dial and Vernier calipers to quickly measure centerline distances.

Product Details:

• Finely grounded base surface and secure locking clamp.